两级跑偏开关是一种安装在皮带，胶带，带式输送上的一种保护装置，当运行中比皮带，胶带，带式输送机发生跑偏时，跑仿角度达到本装置的角度时，本开关能给出报警信号，跑偏角度达到本开关设定的二级角度时，给处于跑偏运行中，皮带，胶带，带式输送机给出停机信号，让处于异常运行中皮带机，停止工作，当经过的将皮带机调整到正常状态时，本保护装置立即自己复位，给处于停机状态的皮带，胶带，带式输送机发生工作信号，皮带输送带，将开始工作，本开关因安装方便，响应，工作角度可根据客户实际使用情况来作相对调整，现用于各行各业。

Switch is a kind of two-stage wandering installed on the belt, adhesive tape, a protection device on the belt conveyor, when running more than belt, belt, belt conveyor running deviation occurs, running Angle Angle to reach the level of the apparatus, the switch can give alarm signal, and set the switch running deviation Angle secondary Angle, to run in the wandering, belts, belt, belt conveyor, stop signal is given, and let the abnormal operation of the belt conveyor, stop working, and when the staff will be adjusted to normal of belt conveyor, this protection device reset, immediately to a stop condition of belt, adhesive tape, signs work belt conveyor, belt conveyor, will begin to work, this switch for easy installation, fast response, working Angle can be adjusted according to the customer actual usage for relative, is now widely used in all walks of life.Switch is a kind of two-stage wandering installed on the belt, adhesive tape, a protection device on the belt conveyor, when running more than belt, belt, belt conveyor running deviation occurs, running Angle Angle to reach the level of the apparatus, the switch can give alarm signal, and set the switch running deviation Angle secondary Angle, to run in the wandering, belts, belt, belt conveyor, stop signal is given, and let the abnormal operation of the belt conveyor, stop working, and when the staff will be adjusted to normal of belt conveyor, this protection device reset, immediately to a stop condition of belt, adhesive tape, signs work belt conveyor, belt conveyor, will begin to work, this switch for easy installation, fast response, working Angle can be adjusted according to the customer actual usage for relative, is now widely used in all walks of life.

 

持术参数

产品名称：两级跑偏开关

产品型号：JSB-KPP-12-30

产品品牌：HANGRONG/杭荣

工作电压：24-380V，电源适用性广

触点数量：双开关触点，容量可选1-1

输出方式：两常开+两常闭，可定制加工单独常开，或常闭。

外壳材料：铝苾压铸，可定制加工304不锈钢材料外壳。

生产厂家：湖北杭荣电气有限公司。

使用环境介绍

工作温度：-20-60度，环境温度可根据客户使用要求定制加工耐温， ，耐温，防爆，防粉尘，等持术规格产品。

相对湿度：不大于85%

产品通用名称

两级跑偏开关，纠偏开关，防偏开关，跑偏控制器

安装说明

1、两级跑偏开关底座两边各有Ф12mm孔，在皮带机旁角铁架钻Ф12mm孔，用M10×30mm螺丝紧固跑偏开关。

2、安装跑偏开关应选择输送装置易出现跑偏的位置处安装，参考应用单位工艺要求，同时要考虑皮带与挡轮的有效间距和推力，建议皮带与档轮间的安装距离为120-160mm

3、安装距离：建议每50米安装一对跑偏开关。

4、跑偏开关出厂时配有长度0.5米四芯橡套电缆，芯线上配有1、2、3、4线号，其中1、2为常开接点是报警信号，3、4为常闭接点是二级停机信号。

5.产品安装接线时，请按照产品说明书来接线，不可自行改变接线方法。

注意事项

1、跑偏开关档轮与皮带保持垂直。

2、建议跑偏开关挡轮与皮带边缘距离保持120-160mm。

3、跑偏开关底座固定牢固。

 

 产品外形尺寸图

 

企业名：湖北杭荣电气有限公司

类型：原厂制造商

电话： 0713-2115868
0713-2115858
0713-2115868

手机：13593699788
15926773610
18807258870

联系人：陈荣/何杭/何宽松

QQ：

邮箱：634540716@qq.com

地址：湖北黄冈麻城龙池工业区杭荣科技园