国产
FPC连接器0.3/0.5/0.8/1.0/1.25mm间距连接器,产品全,质量*,价格优惠.JS-23
PCB
发光二*管
ZIF
单卡
TF
条形
熔接
*潮
磷铜
LCP
企业名:深圳市钜硕电子有限公司
类型:
电话: 0755-28053578
联系人:幸坤新
地址:广东深圳观兰街道办环观中路37栋标准厂房.
产 品 规 格 书
PRODU* SPECIFICATION
【1】适用范围 SCOPE
本规格书适用于:0.5/1.0/1.25间距柔性扁平电缆连接器(有锁式)
This specification covers the 0.5mm Pitch FPC/FFC Connectors(series Locking)
【2】产品名称及型号 PRODU* NAME AND PART NU*ER
产品名称Product Name | 产品型号Part Number |
FFC/FPC扁平电缆连接器 |
|
|
|
【3】定格 RATINGS
项目 Item | 规 格 Requirement | ||
*大容许电压 Rated Voltage(MAX) | 50V | [AC/DC(*值 Virtual value)50Hz] | |
*大容许电流 Rated Current(MAX) | 0.4A | ||
使用温度范围 Ambienttemperature Range | -25℃~ 85℃ | ||
【4】性能 PERFORMANCE
4.1电气性能 Electrical Performance
项目Item | 条 件 Test Condition | 规格Requirement | |
4.1.1 | 接触电阻 Contact Resistance | 适合FPC/FFC嵌合;开放电压20mV以下;短路电流10mA的状态下测定。 Mate applicable FPC/FFC and measure by dry circuit,20mV MAX,10mA. | ≤20 mΩMAX |
4.1.2 |
*缘电阻 Insulation Resistance | 适合FPC/FFC嵌合;相邻端子间或端子与地面间加DC 500V下测定。 Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500MΩMIN |
4.1.3 |
耐电压 Dielectric | 适合FPC/FFC嵌合;相邻端子间或端子与地面间加AC 200V(*值)历时1分钟下测定。 Mate applicable FPC/FFC and apply 200V AC(virtual value)for 1minute between adjacent terminal or ground. | 无击穿现象 No Breakdown |
4.2机械性能 Mechanical Performance
项目Item | 条 件 Test Condition | 规格Requirement | |
4.2.1 | 锁紧力及拔出力 Locking and Withdrawal Force | 适合0.3mm厚的FFC;用每分钟25&plu*n;3mm的速度;平行地*、锁紧、拔出。 Insert and extract applicable FFC at the speed rate of 25&plu*n;3mm/minute. | 锁紧力Locking 1.96*n (N) MAX 拔出力Withdrawal 0.49*n (N) MIN |
4.2.2 | 端子保持力 Terminal /Housing Retention Force | 以用每分钟25&plu*n;3mm的速度平行向外拉 Pull the terminal at the speed rate of 25&plu*n;3mm per minute | 3.92N MIN |
4.3环境和其他性能 Environmental Performance and Others
项目Item | 条 件 Test Condition | 规格Requirement | ||
4.3.1 | 重复插拔 Repeated Insertion and Withdrawal | 无通电状态;以10次/分钟的速度插拔20次 Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute | 接触* Contact Resistance | 60 mΩMAX |
4.3.2 | 温度上升 Temperature Rise | 适合FPC/FFC嵌合;*大容许电流通电,温度测定。(UL 498) Carrying rated current load.(UL 498) | 温度上升 Temperature Rise | 30℃MAX |
项目Item | 条 件 Test Condition | 规格Requirement | ||
4.3.3 |
耐振动性 Vibration | DC 1mA通电状态下;嵌合轴沿XYZ三个方向振动;振幅1.5mm;频率10-55-10Hz/分;历时2小时 Amplitude:1.5mm P-P Sweep time:10-55-10Hz in 1 minute Duration:2 hours in each X.Y.Z. axes | 外观 Appearance | *坏 No Damage |
接触* Contact Resistance | 60 mΩMAX | |||
瞬断 Discontinuity | 1 ms MAX. | |||
4.3.4 |
耐冲击性 Shock | DC 1mA通电状态下;嵌合轴沿相互垂直的6个方向;以490m/s2{50G}冲击;各3次 490m/s2{50G},3 strokes in each X.Y.Z. axes. | 外观 Appearance | *坏 No Damage |
瞬断 Discontinuity | 1 ms MAX. | |||
4.3.5 |
耐热性 Heat Resistance | 适合FPC/FFC嵌合;85&plu*n;2℃的空气中;放置96小时;再回到室温中放置1-2小时 85&plu*n;2℃,96 hour | 外观 Appearance | *坏 No Damage |
接触* Contact Resistance | 60 mΩMAX | |||
4.3.6 |
耐寒性 Cold Resistance | 适合FPC/FFC嵌合;-40&plu*n;2℃的空气中;放置96小时;再回到室温中放置1-2小时 -40&plu*n;2℃,96 hour | 外观 Appearance | *坏 No Damage |
接触* Contact Resistance | 60 mΩMAX | |||
4.3.7 |
耐湿性 Humidity |
适合FPC/FFC嵌合;40&plu*n;2℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定
Temperature:40&plu*n;2℃ Relative Humidity:90-95% Duration:96 Hours | 外观 Appearance | *坏 No Damage |
接触* Contact Resistance | 60 mΩMAX | |||
耐电压 Dielectric Strength | *须满足4.1.3 Must meet 4.1.3 | |||
*缘* Insulation Resistance | 20 MΩMIN | |||
4.3.8 |
温度循环 Temperature Cycling | 适合FPC/FFC嵌合;-55&plu*n;3℃ 30分钟;常温常湿 10-15分钟;85&plu*n;2℃ 30分钟;常温常湿 10-15分钟,循环5次。 5 cycles of: a) -55&plu*n;3℃ 30 minutes b) 85&plu*n;2℃ 30 minutes | 外观 Appearance | *坏 No Damage |
接触* Contact Resistance | 60 mΩMAX |
项目Item | 条 件 Test Condition | 规格Requirement | ||
4.3.9 |
耐盐雾性 Salt Spray | 适合FPC/FFC嵌合;35&plu*n;2℃、5&plu*n;1%的盐水喷雾48小时;试验后常温水洗;再室温干燥。 48&plu*n;4 hours exposure to a salt spray from the 5&plu*n;1% solution at 35&plu*n;2℃. | 外观 Appearance | *坏、腐蚀 No Damage |
接触* Contact Resistance | 60 mΩMAX | |||
4.3.10 |
耐亚* SO2 Gas | 适合FPC/FFC嵌合;40&plu*n;2℃、50&plu*n;5ppm的亚*中放置24小时 24 hours exposure to 50&plu*n;5ppm. SO2 gas at 40&plu*n;2℃. | 接触* Contact Resistance | 60 mΩMAX |
4.3.11 |
耐氨性 NH3 Gas | 适合FPC/FFC嵌合;浓度为28%的*容器中;放置40分钟。 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution | 外观 Appearance | *坏 No Damage |
接触* Contact Resistance | 60 mΩMAX | |||
4.3.12 |
可焊性 Solder ability | 端子前端基准面0.2mm处浸入235&plu*n;5℃的锡槽中;历时2&plu*n;0.5 sec。 Soldering Time:2&plu*n;0.5 sec. Soldering Temperature:235&plu*n;5℃ 0.2 mm from terminal tip | 沾敷性 Solder Wetting | 沾敷面积95%以上
|
4.3.13 |
耐焊接热 Resistance to Soldering heat | 端子前端基准面0.2mm处浸入260&plu*n;5℃的锡槽中;历时5&plu*n;0.5 sec。 Soldering Time:5&plu*n;0.5 sec. Soldering Temperature:260&plu*n;5℃ 0.2 mm from terminal tip | 外观 Appearance | *坏、变形 No Damage |
( ):参考规格Reference Standard
{ }:参考单位Reference Unit
【5】外观形状、寸法及材质PRODU* SHAPE,DIMENSIONS AND MATERIALS
图面参照 Refer to the drawing.
名称 NAME | 材质 MATERIALS |
主体Main body | LCP(本色) UL 94V-0 |
锁扣Housing Lock | LCP(黑色) UL 94V-0 |
端子Sit uip | 磷青铜 Phosphor Bronze |
焊片Contact | 磷青铜 Phosphor Bronze |
备注Remark | 金属表面镀锡 |
"
友情链接: 深圳市元东发电子有限公司