国产
轴向独石电容*42-103M17Y500P52
独石
旁路
圆柱形
小功率
中频
固定
轴向引出线
&plu*n;20(%)
50(V)
企业名:肇庆市国恒电子有限公司
类型:
电话: 0758-6831078
联系人:伦伟平
地址:广东肇庆广东省肇庆市端州区河旁管理区
电气性能标准THE STANDARD OF THE ELE*RICAL PROPERTICAC
检验项目 ITEM | 检验标准 T*T STANDARD | ||||||
NPO(N) COG(CG) | X7R(B) | Z5U(E) | Y5V(Y、F)
| ||||
电容量(C) Capacitance | 在相应的误差 范围内 In the tolerance | 在相应的误差 范围内 In the tolerance | 在相应的误差 范围内 In the tolerance | 在相应的误差 范围内 In the tolerance | |||
损耗角正切(DF) Dissipation Factor | CR≥50pF DF≤0.15% CR<50pF DF≤1.5[(150/CR) 7] ×10-4 |
≤3.5% |
≤5% |
≤3.5%(150000PF以下) ≤10%(220000-470000PF) ≤15%(48PF) | |||
*缘电阻(IR) Insulation Resistance | C≤ 10nF R>10000 MΩ C> 10nF R.C> 100S | C≤ 25nF R>4000 MΩ C> 25nF R.C> 100S | C≤ 25nF R>4000 MΩ C> 25nF R.C> 100S | C≤ 25nF R>4000 MΩ C> 25nF R.C> 100S | |||
耐电压 Dielectric Withstanding Voltage |
2.5倍额定电压 2.5×rated Voltage |
2.5倍额定电压 2.5×rated Voltage |
2.5倍额定电压 2.5×rated Voltage |
2.5倍额定电压 2.5×rated Voltage | |||
测试条件 T*T CONDITION | |||||||
测试频率 Test Frequency | 100kHZ (C>1000PF,1KHZ) | 1KHZ | 1KHZ | 1KHZ | |||
测试电压 Test Voltage | 1&plu*n;0.2VDC | 1&plu*n;0.2VDC | 0.3&plu*n;0.2VDC | 0.3&plu*n;0.2VDC | |||
*缘电阻测试电压 Test Voltage of IR | 额定电压 Rated Voltage | 额定电压 Rated Voltage | 额定电压 Rated Voltage | 额定电压 Rated Voltage | |||
环境温度 Temperature |
18℃~25℃ |
18℃~25℃ |
18℃~25℃ |
18℃~25℃ | |||
环境湿度 Humidity |
< 75% |
< 75% |
< 75% |
< 75% | |||
温度系数 Temperature Coefficient | 0&plu*n;30ppm/℃ -55℃to 125℃
| &plu*n;15% -55℃to 125℃ | 22% to–56% 10℃to 85℃ | 30% to-80% -25℃to 85℃ | |||
品质检验项目及*性试验QUALITY INSPE*ION AND RELLABILITY
项目 ITEM | 检验标准 T*T SPECIFICATIONS | 检验方法 T*T METHODS | ||||||
可焊性 Solderablity
| 引线表面均匀沾锡,上锡面积不小于总面积的75%。 Lead wire shall be soldered with uniformly coated on the axial or radial direction over 3/4 of the circumferential direction. | 将电容器引线浸入含25%酒精(或异丙醇)的松香溶液后浸入焊接槽温度为235&plu*n;5℃的焊锡中2&plu*n;0.5秒,浸入深度距离电容体2.5~3.0mm。 The lead wire of a capacitor shall be dipped into a 25% methanol solution of rosin and then into molten solder of 235&plu*n;5℃ for 2&plu*n;0.5 seconds ,in both cases the depth of dipping is up to about 2.5 to 3.0 mm from the root of lead wires. | ||||||
耐焊性 Resistance To soldering heat
| 外观 Appearance | *伤 No marked defect | 焊锡温度265&plu*n;5℃,时间5&plu*n;0.5秒,*深度距离电容体2.5~3.0mm,*速度1秒,试验后2~24小时测量。 The lead wire shall be immersed into the melted solder of 265&plu*n;5℃,up to about 2.5 to 3.0mm from the main body for 5&plu*n;0.5 sec and the specified items shall be measured after leaving for 2 to 24 hours. | |||||
容量变化ΔC/C Capacitance change | NPO:≤5% X7R:≤-5~ 10% Y5V:≤-10~ 20% | |||||||
介电强度(引线间) Dielectric strength(between lead wires) | 不失效 No failure | |||||||
耐久性 List test | 外观 Appearance | 无外观损伤 No marked defect | 条件 Condition | NPO | X7R | Y5V | Z5U | |
容量变化ΔC/C Capacitance change | NPO:≤2% X7R:≤20% Y5V:≤30% | 温度 Temperature | 125℃ | 85℃ | ||||
D.F. | NPO:≤0.3% X7R:≤5% Y5V:≤7% | 时间 Time | t=1000h | |||||
R.C>25S | 电压 Voltage | V=1.5Vr | ||||||
恢复时间 Recovery time | 24&plu*n;1h | |||||||
引出端强度 Strength of Lead temination |
拉力 Pull |
引线不断 电容器不破损 Lead wire shall not cut off. Capacitor shall not be broken. | 如图:固定电容器并加力,引线直径0.5mm以上加力3kg,保持5秒 As a figure, fix the body of capacitor, apply a tensile weight gradually to each lead in the radial direction of capacitor up to 2 okgf, and keep it for l to 5 sec. |
G | ||||
折弯 Bending | 引线负荷0.5kg向一方向折弯900后恢复原位,再向反方向折弯900恢复原状为,共3次。 Each lead wire shall be subjected to 0.5kgf weight and then a 900bend at the point of egress, in one direction, return to original position and then a 900bend in the opposite direetion at the rate of one bend. | |||||||
公司名称:广东省肇庆市国恒电子有限公司
地址:广东省肇庆市黄岗镇河旁管理区河旁东
伦伟平
手机:: 86- 传真: 86-
:GOLD.HOPE@163.CON
https://zqgoldhope.cn.alibaba.com
友情链接: 深圳市元东发电子有限公司