FPC0512-20RL-TAGT
国产
企业名:深圳市尤瑞尔电子有限公司
类型:生产企业
电话: 0755-88600755
手机:13570854201
联系人:代先生
邮箱:kevin-dai@urael-hk.com
地址:广东深圳福田区上步工业区101栋四楼Y22
FPC连接器0512系列(0.5间距 1.2H)
【1】适用范围 SCOPE
本规格书适用于:0.5/1.0/1.25间距柔性扁平电缆连接器(有锁式)
This specification covers the 0.5mm Pitch FPC/FFC Connectors(series Locking)
【2】产品名称及型号 PRODUCT NAME AND PART NUMBER
产品名称 Product Name |
产品型号Part Number |
FFC/FPC扁平电缆连接器 |
|
|
|
【3】定格 RATINGS
项目 Item |
规 格 Requirement |
||
容许电压 Rated Voltage(MAX) |
50V |
[AC/DC(有效值 Virtual value)50Hz] |
|
容许电流 Rated Current(MAX) |
0.4A |
||
使用温度范围 Ambient temperature Range |
-25℃ ~ +85℃ |
||
【4】性能 PERFORMANCE
4.1电气性能 Electrical Performance
项目 Item |
条 件 Test Condition |
规格 Requirement |
|
4.1.1 |
接触电阻 Contact Resistance |
适合FPC/FFC嵌合;开放电压20mV以下;短路电流10mA的状态下测定。 Mate applicable FPC/FFC and measure by dry circuit,20mV MAX,10mA. |
≤20 mΩMAX |
4.1.2 |
绝缘电阻 Insulation Resistance |
适合FPC/FFC嵌合;相邻端子间或端子与地面间加DC 500V下测定。 Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. |
500MΩMIN |
4.1.3 |
耐电压 Dielectric |
适合FPC/FFC嵌合;相邻端子间或端子与地面间加AC 200V(有效值)历时1分钟下测定。 Mate applicable FPC/FFC and apply 200V AC(virtual value)for 1minute between adjacent terminal or ground. |
无击穿现象 No Breakdown |
4.2机械性能 Mechanical Performance
项目 Item |
条 件 Test Condition |
规格 Requirement |
|
4.2.1 |
锁紧力及拔出力 Locking and Withdrawal Force |
适合0.3mm厚的FFC;用每分钟25±3mm的速度;平行地插入、锁紧、拔出。 Insert and extract applicable FFC at the speed rate of 25±3mm/minute. |
锁紧力 Locking 1.96*n (N) MAX 拔出力 Withdrawal 0.49*n (N) MIN |
4.2.2 |
端子保持力 Terminal /Housing Retention Force |
以用每分钟25±3mm的速度平行向外拉 Pull the terminal at the speed rate of 25±3mm per minute |
3.92N MIN |
4.3环境和其他性能 Environmental Performance and Others
项目 Item |
条 件 Test Condition |
规格 Requirement |
||
4.3.1 |
重复插拔 Repeated Insertion and Withdrawal |
无通电状态;以10次/分钟的速度插拔20次 Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute |
接触抵抗 Contact Resistance |
60 mΩMAX |
4.3.2 |
温度上升 Temperature Rise |
适合FPC/FFC嵌合;容许电流通电,温度测定。(UL 498) Carrying rated current load.(UL 498) |
温度上升 Temperature Rise |
30 ℃MAX |
项目 Item |
条 件 Test Condition |
规格 Requirement |
||
4.3.3 |
耐振动性 Vibration |
DC 1mA通电状态下;嵌合轴沿XYZ三个方向振动;振幅1.5mm;频率10-55-10Hz/分;历时2小时 Amplitude:1.5mm P-P Sweep time:10-55-10Hz in 1 minute Duration:2 hours in each X.Y.Z. axes |
外观 Appearance |
无损坏 No Damage |
接触抵抗 Contact Resistance |
60 mΩMAX |
|||
瞬断 Discontinuity |
1 ms MAX. |
|||
4.3.4 |
耐冲击性 Shock |
DC 1mA通电状态下;嵌合轴沿相互垂直的6个方向;以490m/s2{50G}冲击;各3次 490m/s2{50G},3 strokes in each X.Y.Z. axes. |
外观 Appearance |
无损坏 No Damage |
瞬断 Discontinuity |
1 ms MAX. |
|||
4.3.5 |
耐热性 Heat Resistance |
适合FPC/FFC嵌合;85±2℃的空气中;放置96小时;再回到室温中放置1-2小时 85±2℃,96 hour |
外观 Appearance |
无损坏 No Damage |
接触抵抗 Contact Resistance |
60 mΩMAX |
|||
4.3.6 |
耐寒性 Cold Resistance |
适合FPC/FFC嵌合;-40±2℃的空气中;放置96小时;再回到室温中放置1-2小时 -40±2℃,96 hour |
外观 Appearance |
无损坏 No Damage |
接触抵抗 Contact Resistance |
60 mΩMAX |
|||
4.3.7 |
耐湿性 Humidity |
适合FPC/FFC嵌合;40±2℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定
Temperature:40±2℃ Relative Humidity:90-95% Duration:96 Hours |
外观 Appearance |
无损坏 No Damage |
接触抵抗 Contact Resistance |
60 mΩMAX |
|||
耐电压 Dielectric Strength |
必须满足4.1.3 Must meet 4.1.3 |
|||
绝缘抵抗 Insulation Resistance |
20 MΩ MIN |
|||
4.3.8 |
温度循环 Temperature Cycling |
适合FPC/FFC嵌合;-55±3℃ 30分钟;常温常湿 10-15分钟;85±2℃ 30分钟;常温常湿 10-15分钟,循环5次。 5 cycles of: a) -55±3℃ 30 minutes b) 85±2℃ 30 minutes |
外观 Appearance |
无损坏 No Damage |
接触抵抗 Contact Resistance |
60 mΩMAX |
项目 Item |
条 件 Test Condition |
规格 Requirement |
||
4.3.9 |
耐盐雾性 Salt Spray |
适合FPC/FFC嵌合;35±2℃、5±1%的盐水喷雾48小时;试验后常温水洗;再室温干燥。 48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃. |
外观 Appearance |
无损坏、腐蚀 No Damage |
接触抵抗 Contact Resistance |
60 mΩMAX |
|||
4.3.10 |
耐亚硫酸 SO2 Gas |
适合FPC/FFC嵌合;40±2℃、50±5ppm的亚硫酸中放置24小时 24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. |
接触抵抗 Contact Resistance |
60 mΩMAX |
4.3.11 |
耐氨性 NH3 Gas |
适合FPC/FFC嵌合;浓度为28%的氨水容器中;放置40分钟。 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution |
外观 Appearance |
无损坏 No Damage |
接触抵抗 Contact Resistance |
60 mΩMAX |
|||
4.3.12 |
可焊性 Solder ability |
端子前端基准面0.2mm处浸入235±5℃的锡槽中;历时2±0.5 sec。 Soldering Time:2±0.5 sec. Soldering Temperature:235±5℃ 0.2 mm from terminal tip |
沾敷性 Solder Wetting |
沾敷面积95%以上
|
4.3.13 |
耐焊接热 Resistance to Soldering heat |
端子前端基准面0.2mm处浸入260±5℃的锡槽中;历时5±0.5 sec。 Soldering Time:5±0.5 sec. Soldering Temperature:260±5℃ 0.2 mm from terminal tip |
外观 Appearance |
无损坏、变形 No Damage |
【5】外观形状、寸法及材质PRODUCT SHAPE,DIMENSIONS AND MATERIALS
图面参照 Refer to the drawing.
名 称 NAME |
材 质 MATERIALS |
主体 Main body |
LCP(本色) UL 94V-0 |
锁扣 Housing Lock |
LCP(黑色) UL 94V-0 |
端子 Sit uip |
磷青铜 Phosphor Bronze |
焊片 Contact |
磷青铜 Phosphor Bronze |
备注 Remark |
金属表面镀锡 |
企业名:深圳市尤瑞尔电子有限公司
类型:生产企业
电话: 0755-88600755
手机:13570854201
联系人:代先生
邮箱:kevin-dai@urael-hk.com
地址:广东深圳福田区上步工业区101栋四楼Y22
友情链接: 深圳市元东发电子有限公司