●特征Properties:    ◇探头安装时没有刻线标志及方向性要求。
    ◇用在齿轮、齿条或凹凸不平的导磁金属上，作计数、定位、检测。被测齿轮的齿间距可以小到1.5-2mm。
    ◇输出接线为NPN型、PNP型通用。
    ◇耐恶劣环境，如油、水、粉尘等。
    ◇具的分辨率和极高的重复性。
    ◇宽频响，可在80Hz~33KHz中使用。
    ◇抗电磁干扰大。
    ◇适用于村田33H加弹机、NO741、777、778……卷绕头摩擦辊、锭子、横动轴测速探头，（PG1、PG2、PG3。型号PA1015A）；帝人卷绕头锭子、横动轴测速探头（PU2、PU3、PU4。型号EM-014）；中丽BKV系列高速卷绕头等。◇The probe installation has no line mark and directional request.
◇Applied to count, orient or test for gear, rack or uneven magnetic metal, the teeth interval of the gear wheel can be less than 1.5-2mm.
◇The output terminal is NPN type, PNP is common.  
◇Endure bad environment, such as oil, water or dust etc….
◇Excellent distinguishing rate and high repetition.
◇Wide band, can be used within 80HZ~33KHz.
◇High anti- electromagnetic interference
◇Applied to Murata 33H feeder, NO741, 777, 778….. Winding friction stick, spindle, transverse axle velometer probe, (PG1, PG2, PG3, type: PA1015A), Teijin winding spindle, transverse axle velometer probe, (PU2, PU3, PU4, type: EM-014), high speed drawing….    本产品推荐检测间隙（探头表面与齿顶之间）为1mm±20%，建议安装传感器时，用塞尺准确调整该间隙。为了使输出达到效果，当齿轮信号频率大于15kHz，齿轮安装的径向跳动应小于0.03mm，当齿轮信号频率小于15kHz时，齿轮安装的径向跳动应小于0.1mm。
    因传感器内部有永磁体，安装时应注意避免齿轮与传感器头之间因吸引而产生撞击，而使传感器损坏。
    传感器测量时无方向性。
    注意：若周围电磁干扰大，建议将屏蔽线妥善接地，接地位置在接收装置输入端的地线点上。
The recommend testing clearance (Between surface of probe and tooth top) is 1mm ±20%, suggest to adjust the clearance with proof stick while install the sensor. In order to make output to be best effect, if the gear signal frequency is larger than 15 kHz, make sure the radial beats of gear to be less than 0.1mm, while the gear signal frequency is smaller than 15 kHz, the radial beats could be less than 0.3mm.
For there are permanent magnet inside the sensor, please avoid impact on the sensor, and result in sensors' damage.
The sensor has no direction requirement when do measurement.
Note: If the electromagnetic disturbance around is strong, suggest make proper ground to screened cable, the ground position should be placed at the GND point of input terminal of receiving equipment.

企业名：上海光洋欧克电子科技发展有限公司

类型：生产企业

电话： 86 021 51060266-610

手机：13918420898

地址：广东广州中国上海上海市上海市闸北区江场三路307号