1. 安规标准 / SAFETY STANDARD
电源*合下列的国际标准:The power supply shall be certified by the following international regulatory standards:
  Country Certified Status 标准
Standard
UL 美洲
Europe MEET UL60950，UL8750
CE 欧洲
Europe MEET EN61347-1，/-2-13
2. 输入特性 / INPUT FEATURE
2.1 输入电压范围/INPUT VOLTAGE RANGE：180Vac to 264Vac
2.2 额定输入电压/RATED INPUT VOLTAGE: 200Vac to 240Vac
2.3 输入频率范围/INPUT FREQUENCY RANGE: 50Hz
2.4 额定工作频率/RATED INPUT FREQUENCY: 60Hz
2.5 输入180Vac条件额定负载时*大输入电流不*过0.1A.
INPUT CURRENT:0.1A max.&180Vac.
2.6 在冷开机条件下,*大浪涌电流不*过 8A (输入240Vac额定负载时).
INRUSH CURRENT: 8A max. at 240Vac input for a cold start at 25oC.
2.7 效率：＞75% (输入180-240Vac、90-135Vac和输出满载条件).
EFFICIENCY: higher than 75% at 180-240Vac 90-135Vac input and output full loa
3. 输出特性 / OUTPUT FEATURE
额定输出电压: 12VDC-55V
RATED OUTPUT VOLTAGE 规格限定/SPEC. LIMIT
Min. value Max. value
空载输出电压
Unload output regulation 不可空载 不可空载
负载输出电压
Rated load output voltage 12 VDC 45VDC
额定输出电流
Rated output current 0.015 A 0.15A
短路输出功率
Short-circuit output power Hiccup mode
hiccup(3W)
电压调整率
Line regulation ≤5%
负载调整率
Load regulation ≤5%
输出纹波及噪声/Ripple and Noise
(20MHz Bandwidth 10uF Ele.Cap. & 0.1uF Cer. Cap.) ≤600 mVp-p.
输出瞬态响应/Transient response
(Output load change from 20% to 80% of full load ≤1000mV4. 保护特性 / PROTE*ION FEATURE4.1 OVER - CURRENT PROTE*ION: The power supply shall be hiccupped and no damage shall occur when output current reaches to its over-current protection trigger point
4.2 SHORT - CIRCUIT PROTE*ION: The power supply shall be hiccupped and no damage shall occur when any output operating in a short circuit condition under any line condition for an indefinite period of time.
4.3 OVER - VOLTAGE PROTE*ION: The power supply shall be hiccupped and no damage shall occur when output current reaches to its over- voltage protection trigger point
5. 环境条件 / ENVIRONMENTAL CONDITIIONS
5.1 操作条件: 在下列环境条件下,电源能够连续工作在各种模式,且*性能的退化.
OPERATING: The power supply shall be capable of operating continuously in any mode without performance deterioration in the following environmental conditions.
5.1.1 环境温度: 0℃～40℃
Ambient Temperature: 0℃～40℃
5.1.2 相对湿度: 10%～90%
Relative Humidity: 10%～90%
5.1.3 Vibration: 1.0mm, 10–25Hz, 15 minutes per cycle for each axis (X, Y, Z)
5.2 非操作条件: 电源能够长期的经受下列的环境条件,且不允许有电气及机械方面的损伤和幷发工作的缺陷.
*N-OPERATING: The power shall be capable of withstanding the following environmental conditions extended periods of time, without sustaining electrical or mechanical damage and subsequent operational deficiencies
5.2.1 环境温度: -30℃～70℃
Ambient Temperature: -30℃～70℃
5.2.2 相对湿度: 10%～90%
Relative Humidity: 10%～90%
5.2.3 振动和冲击: 电源供应器装配及出货的包装设计,均能承受正常运输的振动. 并*合
MIL–STD-810D 方法 514 和程序 X.
Vibration and Shock :The power supply shall be designed to withstand normal transportation vibration per MIL–STD-810D, method 514 and procedures X, as it is mounted in the ch*is *embly and packed for shipping.
5.2.4 跌落试验:电源产品能在装运过程中,由于意外跌落之地面及水泥地(*高1.55M) 落下顺序为三菱六面且不允许有电气及机械方面的损伤和幷发工作的缺陷.
Drop Test ：Power supply product can in transport process, because the accident drops into its ground and cement ground( tallest 1.55 Ms)s fall in in proper order for Mitsubishi six,without sustaining electrical or mechanical damage and subsequent operational deficiencies

6. 电磁兼容性标准 / EMC STANDARDS
6.1 EMI 标准/ EMI STANDARDS
本电源供应器*合辐射及传导之限定要求，满足,EN EN55015
The power supply met the radiated and conducted emission requirements requirements for
, EN55015，
7. *性及品质控制 / RELIABILITY AND QUALITY CONTROL
7.1 老化: 电源在35℃&plu*n;5℃ 和满载条件下老化 8 小时.
BURN-IN: The power supply shall under go a minimum of 8 hours Burn-In test under full load at 35℃&plu*n;5℃.
7.2 元件温度要求:半导体结温不允许*过其制造商要求的*大温度值.
COMPONENT DERATING: Semiconductor junction temperatures shall not exceed the manufacturer’s maximum thermal rating.
7.3 平均故障间隔时间: 在25℃条件下,电源供应器在规格限定内工作,其MTBF*少要 50,000 小时.
MTBF: When the power supply is operating within the limits of this specification the MTBF shall be at least 50,000 hours at 25℃ (MIL-STD-217F).
8. *缘介电强度（耐压）/ DIELE*RIC WITHSTANDING STRENGTH (HI-POT)
输入对输出端、输入对壳体之间施加3750V交流电压测试1分钟（漏电流≤5mA），无击穿或飞弧现象。(量产测试用3秒钟).
Primary to Secondary & Case AC3750V, 1 minute(leakage current less than5mA) for t*e test, (3 second for production).
9. *缘阻* / INSULATION R*ISTANCE
输入对输出*缘阻*用500VDC测试时不小于 50 兆欧姆.
Input to output: no less than 50 MOHM(500VDC)
 
10. 漏电流 / LEAKAGE CURRENT
当电源供应器工作在*大输入及*大负载情况下,其漏电流小于 0.25 mA, 满足Cl* ‖等级.
The leakage current shall be less than 0.25 mA for Cl* ‖ when power supply is operated maximum input voltage and maximum load.

企业名：深圳市柏砾电源有限公司

类型：生产企业

电话：

手机：13510554506

联系人：代亚辉

地址：广东深圳中国 广东 深圳市宝安区 石岩镇水田社区祝龙田路114号新太阳工业园1栋4楼B区