1.規格型號和安規認證
MODEL NU*ER AND SAFETY CERTIFICATION
Model Number: Part Number Rated Current Rated Voltage Approvals.
例子[example]:
2F/2T 1.25A 250V 1)系列號 Part Number
2)額定電流 Rated Current
1） 2） 3） 3)額定電壓 Rated Voltage
1-2 額定電流和額定電壓
Rated Current And Voltage
額定電流： 32mA~15A
Rated Current: 32 mA~15A
額定電壓;125V/250V/400V AC
Rated Voltage:125V/250V/400 AC
1-3標示Marking
保險絲上需有下列標示
The fuse shall have the following marking:
規格：特性*號 額定電流 額定電壓
Specification:Characteristic Symbol Rated Voltage
32mA~800mA : _mA 1A~15A:_A
Trade mark:The Manufacture’s Logo Part Number Approvals
![]()
![]()
32mA~15A:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍
SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRU*URE
3-1 工程圖（單位：mm）
Outline Drawing and Dimensions(Unit:mm)
3-2結構
Structure
編號
No. | 元件
Component | 材質
Material | 數量
Quantity |
| (1) | 熔絲
Wire | 合金
Alloy | 1 |
| (2) | 銅帽
Cap | 黃銅鍍鎳
Br* with mickel plated | 2 |
| (3) | 本體
Body | 陶瓷管/胶料
Ceramic Tube/Plastic | 1 |
| (4) | 引線
Lead | 鍍錫銅線
Tinned Copper wire | 2 |
| (5) | 镀层
Insulating Coat | 环氧树脂
Epoxy Resin | / |
4.外觀及形狀
APPEARANC* AND CONFIGURATION
4-1外觀：外观不应有显著的污点、铁锈或者裂纹
Appearances:There shall not be any remaekable stain,rust or crack on the appearances.
4-2形狀：轴向引脚的*小型保险丝
Configuration:Axial Leaded Micro-Fuse.
5.物理特性
PHYSICAL CHARA*ERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力，持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.電氣特性
ELE*RICAL CHARA*ERISTICS
| % of Ampere Rating | Ampere Rating | Opening Time |
| 100% | 32mA - 15A | 4 Hours, Min. |
| 200% | 32mA - 15A | 60 Second, Max |
| 275% | 500mA~ 10A | 300 msecs., Max. |
| 400% | 500mA~ 10A | 30 msecs., Max. |
| 1000% | 500mA~ 10A | 4 msecs., Max. |
| 规格判定Item |
| Openrating Temp | -55℃~125℃ |
| *大熔断时限 | 200% Rating 60SEC |
| 突波实验 | 3millisecond at 1000% rated current |
| Melting I 2 t | 1.83~2.083 |
| Cold Ohms | 1.25A/0.058~0.067 Ohm |
| Interrupting rating | 50A/125VAC
50A/250VAC |
| Dimensions | 9mm*¢3.9mm |
| Ssfty | UL CSA CCC ROHS |
7.環境特性
ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-55℃~125℃
Operating Temperature: -55℃~125℃
7-2 保存條件
Storage Conditions
溫度： 10℃~60℃
Temperature: 10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露*，相對濕度為95%下*多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度：260&plu*n;5℃
Soldering Temperature:260&plu*n;5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350&plu*n;5℃
Soldering Temperature: 350&plu*n;5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER *TICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.
