NTC9221外场强光投光灯

应C-NTC9221外场强光投光灯 高亮度投光灯，强光投光灯

C-NTC9221外场强光投光灯 　　产品说明：

　　广泛适用于广场、体育场、高尔夫球场、大型建筑物、货柜场、港口、码头等场所作投光照明。

　　1、C-NTC9221外场强光投光灯 性能特点:

　　采用*功率*度气体放电灯作光源，显色指数*合国际奥委会对体育场馆的设计标准，*了彩色电视转播的技术条件和要求。

　　灯具采用全密封结构设计，呼吸过滤装置能够*地平衡灯具内外的空气压力并降低灯具内的温度，从而*灯具的使用寿命。

　　内部装有遮光板，可*控制眩光，减少光污染。

　　采用*新表面处理技术，具有良好的*腐能力，*在恶劣环境下*使用。

　　外壳采用优质轻合金材料制作，外壳结构经过优化设计，重量轻，强度高，具有*强力碰撞和冲击能力。

　　灯具采用一体化造型设计，外形美观，线条流畅，风阻小。

　　人性化的后开盖设计，更换灯泡快捷方便；开盖断电保护装置*大地*了灯具*性。

　　采用座式、壁挂式、吸顶式等多种安装方式, 操作简单方便；灯具两侧有调光刻度盘及瞄准结构，方便调整灯具投射角度，并可根据需要选配红点瞄准器，用于远距离*对光。

　　２、C-NTC9221外场强光投光灯 使用方法：

　　1、根据现场环境和照明需要，确定灯具和镇流器箱的安装位置，备好两根相应长度的三芯电缆线，一根是灯具电缆线，连接灯具的接线盒和镇流器箱，另一根是电源电缆线，用来连接镇流器箱和电源。

　　2、C-NTC9221外场强光投光灯 打开镇流器箱端盖，旋松镇流器箱电缆引入口的压紧螺母，将灯具电缆线、电源电缆线分别穿过压紧螺母引入到镇流器箱内部接线端子处，按接线图的规定将L1线、L2线、地线连接固定，再旋紧电缆线压紧螺母和紧固镇流器箱端盖。

　　3、C-NTC9221外场强光投光灯 按规定的安装方式将灯具和镇流器箱安装好，再将电源电缆线的另一端连接到380V或220V电源。

　　4、C-NTC9221外场强光投光灯 旋松灯具支架两侧的六角头固定螺栓，可在180°范围内调整灯具的照射角度（可通过支架上的刻度盘粗略调节，也可选配红点瞄准器进行*调节），在*所需照射角度后，将灯具两侧的固定螺钉拧紧。

　　5、更换灯泡时，松开灯具后盖上的四个内六角螺钉，打开后盖，拆下灯座上固定灯泡引线端子的两个螺钉，取下坏灯泡，将新灯泡装入灯座并拧紧固定螺钉，将后盖装好。

　　注意：换灯泡时，要将泡壳中间鼓起的泡瘤背向灯具透明件。

　　３、C-NTC9221外场强光投光灯 注意事项：

　　1、安装灯具时，*须将灯具支架上的*固定螺钉拧紧，*灯具在恶劣条件下使用时出现松动而造成危险。由于灯体温度较高，灯具安装应高于3m或应安装在人不易接触的地方。

　　2、灯具使用时，透明件中心及灯具外壳温度较高，不得触摸，以免烫伤。

　　3、灯具在使用时表面不能有任何覆盖物。

　　4、灯具只能完整的带有保护屏使用。

　　5、使用时，灯具与被照物体之间*短距离为7米，以免发生火灾。

　　6、更换灯泡时，不可用手直接触摸灯泡的泡壳，只能接触灯泡两端的瓷柄，否则将会影响泡壳的透光率。如果泡壳表面已有污迹，可用工业酒精清洗。（如光源刚刚熄灭，应使灯具充分冷却都才能进行操作）。

　　7、如果此灯具的外部软缆或软线损坏了，该线要由制造厂或其服务代理商或一个有资格的人更换。

Should C-NTC9221 field light cast light of high brightness light, bright lights cast light lamps
C-NTC9221 outfield light cast light lamps product description:
Widely applicable to the Plaza, stadium, golf course, large buildings, container yards, ports, terminals and other places for illumination.
In 1, C-NTC9221 field light cast light lamps Performance characteristics:
With large power high intensity gas discharge lamp as the light source, the color rendering index accords with the International Olympic Committee on sports venue design standard, achieve color evision technical conditions and requirements.
The lamp adopts fully sealing structure design, respiration filtering device can effectively balance the lamps inside and outside air pressure and lower the temperature inside the lamp, thereby improving the service life of the lamp.
With internal shading plate, which can effectively control the glare, reduce light pollution.
Using the new surface treatment technology, has excellent anticorrosive ability, ensure reliable use in harsh environments.
The shell is made of good quality light alloy material, shell structure optimized design, light weight, high strength, resistant to strong collision and impact resistance.
The lamp adopts integrated design, beautiful shape, *ooth lines, *all wind resistance.
Humanized after opening the cover design, convenient replacement bulb; uncovering power-off protection device greatly ensure the safety lamps.
The seat t*e, hanging t*e, ceiling t*e and so on many kinds of installation, operation is simple and convenient; lamps on both sides of a light adjustable dial and aiming at the structure, convenient to adjust the lighting angle of projection, and according to the need for matching red dot sight, for long range precision of light.
In 2, C-NTC9221 field light cast light lamps using method:
In 1, according to the site environment and lighting needs, determine the lamp and ballast tank installation position, prepared two corresponding lengths of three core cable, a cable connected lamps, lamp and ballast box junction box, the other one is a power cable, used to connect the ballast box and power supply.
In 2, C-NTC9221 field light cast light on ballast box cover, unscrew the ballast box cable export pressing nut, the lamp power supply cable, cable respectively through the nut into the ballast tank internal wiring terminal, according to the wiring diagram of the provisions of the L1 lines, L2 lines, ground connection and fixation, and tightening the cable clamp nut and a ballast box cover.
In 3, C-NTC9221 field light cast light lamps in accordance with the provisions of the lamp and ballast box installation will be installed, then the power cable is connected to the other end to a 380V or 220V power supply.
In 4, C-NTC9221 field light cast light lamps unscrew lamp bracket on six sides of the hexagon head bolt, can be within the range of 180 DEG to adjust the lamp irradiation angle (through the bracket on the dial rough adjustment, also optional red-dot sights are precisely regulated ), upon reaching the desired illumination angle, the lamps on both sides of the fixed screw.
In 5, replacing the light bulb lamp back cover, released on the four inner six angle screws, open the rear cover, remove the fixed on the lamp socket bulb terminal two screws, remove the bad light bulb, bulb into the bulb holder and tighten the new fastening screw, the rear lid.
Note: to change a light bulb, the bubble shell up to intermediate foam aneury* of the dorsal to lighting transparent parts.
In 3, C-NTC9221 field light cast light lamps matters needing attention:
In 1, the installation of lamps, the lamp must be support all the fixed screws, prevent the lamps for use in adverse conditions occur when loosening and dangerous. As the light body temperature is higher, lighting installation should be higher than the 3m or should be installed in places people are not easy to contact.
In 2, the lamp, the transparent center and the lamp shell temperature is higher, not to touch, so as not to burn.
3, lamps in use the surface can not have any covering.
4, lamps can only complete with screen protection use.
In 5, when in use, the lamps and the illuminated objects between the shortest distance is 7 meters, so as to avoid fire.
In 6, replacing the light bulb, do not hand directly touching the bulb in the bulb, can contact the ends of the lamp porcelain handle, otherwise it will affect the light tran*ittance of bubble shell. If the bubble shell surface has a stain, used in industrial cleaning alcohol. ( such as a light source is out, should make the lamps are fully cooling can operate ).
7, if the lamp external flexible cable or cord is damaged, the line is to be by the manufacturer or its service agent or a qualified replacement.
8358770130

企业名：乐清市江北防爆电器有限公司

类型：生产企业

电话： 0577-27772857

手机：13968793493

联系人：吕军帅

QQ：

地址：浙江温州乐清柳市方斗岩工业区