电容产品详细描述：1.范围Scope适用“RVT系列”立式片式铝电解电容器This specification covers “RVT Series” V-chip aluminum electrolytic capacitors.2.参考标准Reference Standard日本工业标准JIS C-5141、JIS C-5102Japanese industrial Standard JIS C-5141 characteristics W and JIS C-5102except as specified in this specification.3.环境保护标准Environmental Protection Standard遵照欧盟指令2002/95/EC.Comply with the EU directive 2002/95/EC.4.使用温度范围Operating Temperature RangeC ~-55 C 1055.电压范围Voltage Range6.3 ~ 100V6.容量范围Capacitance RangeF4.7~ 15007.容量偏差范围Capacitance Tolerance20% at 120Hz, C208.漏电流Leakage Current2分钟后读数A) whichever isI ≤ 0.01 CV or 3 ( greater (after 2 minutes)9.Tan测试频率：120Hz，温度：20℃Measurement frequency: 120Hz, Temperature: C20Rated Voltage (V) 6. 100Tan d (max.) 0.30 0.24 0.20 0.18 0.16 0.14 0.14 0.1410.低温特性Stability at Low Temperature测试频率：120HzMeasurement frequency: 120HzRated Voltage (V) 6. 100Impedance RatioZT/Z20 (max.) Z-25°C /Z 20°C 2 2 2Z-40°C /Z 20°C 3 3 311．耐久性Load Life105℃施加额定电压2000小时后，电容器应满*下要求After 1000 hours application of rated voltage at 105°C, capacitors meet the characteristics requirements listed.容量变化率Capacitance Change &plu*n;30%初始值内Within &plu*n;30% of initial value损耗角正切值Tan d ≤300%初始规定值300% or less of initial specified value漏电流Leakage Current ≤初始规定值Initial specified value or less12.高温储存Shelf Life105℃放置1000小时后，满*下要求After storage for 1000H at 105℃&plu*n;5℃Capacitance Change Within &plu*n;30% of initial valueTan d 200% or less of initial specified valueLeakage Current 300% of less of Initial specified value.13.耐焊接热Resistance to Soldering Heat经过回流焊后（参见第6页）在温室中恢复后，电容器满*下要求After reflow soldering according to Reflow Soldering Condition (see pag8e 5)and restored at room temperature, they meet the characteristics listed.容量变化率Capacitance Change ≤&plu*n;10%初始值Within &plu*n;10% of initial value损耗角正切值Tan d ≤初始规定值Initial specified value or less漏电流Leakage Current ≤初始规定值Initial specified value or less14.标识Marking电容器标识内容如下：Capacitors shall be legibly marked with the following:1）产品系列Manufacture’s mark2）额定电压和额定电容Rated voltage and nominal capacitance3）负*标识Negative polarity15.图样Drawing (Unit: mm)(Æ4~Æ6.3)(Æ8, Æ10)16.尺寸Dimensions (Unit: mm)ÆD´L 4´5.4 5´5.4 6.3´5.4 6.3´7.7 8´6.5 8´10.5 10´10.5A 1.8 2.1 2.4 2.4 2.9 2.9 3.2B 4.3 5.3 6.6 6.6 8.3 8.3 10.3C 4.3 5.3 6.6 6.6 8.3 8.3 10.3E 1.0 1.3 1.8 1.8 3.1 3.1 4.2L 5.4 5.4 5.4 7.7 6.5 10.5 10.517.编带说明Taping Specifications*合标准JIS C0806Applicable standard JIS C0806(RVT、RVS、RVE、RVW、RVK、RVH、RVNseries)盒带Carrier Tape17.1.图样10)4 ~ Drawing 1 (for尺寸DimensionSeries RVTÆD´L 4´5.4 5´5.4 6.3´5.4 6.3´7.7 8´6.5 8´10.5 10´10.5W 12.0 12.0 16.0 16.0 16.0 24.0 24.0P 8.0 12.0 12.0 12.0 12.0 16.0 16.0F 5.5 5.5 7.5 7.5 7.5 11.5 11.5A 4.7 6.0 7.0 7.0 8.7 8.7 10.7B 4.7 6.0 7.0 7.0 8.7 8.7 10.7T2 5.8 5.8 5.8 8.3 7.0 11.0 11.017.2.卷盘Reel包装数量 Package quantityÆD´L 卷装数量Qty./Reel 盒装数量Qty./Bag4´5.5 2000 pcs. 20000 pcs.5, 6.3´5.4 1000 pcs. 10000 pcs.6.3´7.7 1000 pcs. 10000pcs.8´6.5 1000 pcs. 10000 pcs.8´10.5 500 pcs. 5000 pcs.10´10.5 500 pcs. 5000 pcs.ÆD 4 5 6.3 8*6.5 8*10.5 10*10.5A8. 无铅回流焊接Lead-free Reflow Soldering ConditionA. 回流焊条件推荐Recommended Conditions for Reflow Soldering（1）应采用*及热风回流焊接，不宜采用汽相加热回流焊接；A thermal condition system such as infrared radiation (IR) or hot blast should be adopted, and vapor heat transfer systems (*) are not recommended.（2）推荐回流焊只进行，回流焊次数如果需要二次，*须相隔30分钟以上；Reflow soldering should be performed one time. If the capacitor has to be reflowed twice, 30 minutes must be layout between each time.（3）无铅回流焊，请*合下述条件：For lead-free t*e reflow soldering, please observe proper conditions below:a)从150℃至200℃的预热时间在180秒钟以内；The time of preheating from 150°C to 200°C shall be within maximum 180 seconds;b)电容器顶部温度*过217℃的焊接时间不*过tL秒；The time of soldering temperature at 217°C measured on capacitors' * shall not exceed tL (second);c)电容器顶部*温度不*过Tp℃，在5℃范围内的实际*温度时间不*过tp秒The peak temperature on capacitors' * shall not exceed Tp(°C), and the time within 5°C of actual peak temperature shall not exceed tp (second).B.回流焊曲线图Cl*ification Reflow ProfileC. *温度允许范围Allowable Range of Peak TemperatureSize Thickness (mm) Tp(°C) tL (second) tp (second)Æ4~Æ6.3 ³2.5 250&plu*n;0 80 20Æ8 ³2.5 240&plu*n;0 80 10Æ10´10.5L ³2.5 235&plu*n;0 60 10D.表面安装推荐尺寸Recommended Land Size (Unit: mm)Size X Y aÆ4 1.6 2.6 1.0Æ5 1.6 3.0 1.4Æ6.3 1.6 3.5 2.1Æ8 2.5 3.5 3.0Æ10 2.5 4.0 4.019.引线原材料The Raw Materials of Lead WireName Material PercentageTPCS Fe 71.35%Cu 20%Sn 8.65%20.电容器代码标志Explanation of Part NumberSeries (RVT) Voltage (25V) Capacitance (22mF) Capacitance Tolerance (&plu*n;20%) Case Diameter(Æ6.3*5.4mm)范例：21. 结构Construction22.额定纹波电流的频率导数Frequency Coefficient of Allowable Ripple CurrentFrequency 50Hz 120Hz 300Hz 1kHz 10kHz～Coefficient 0.70 1.00 1.17 1.36 1.5023. 电气参数：Electric parameter* Series Name(uF / WV) WV(V) Cap.(uF) Cap. tol.(%)120Hz20℃ DF（％）120Hz20℃≤ LC（uA）（2min）≤ DΦ* L E&plu*n;0.5 Allowable ripple current (mA rms) at 105°C, 120Hz *R100KHz(Ω)20℃≤ Remarks24. 片式铝电解电容器一般使用注意事项Application guideline for V-CHIP aluminum electolytic capacitorsA)电路设计Circuit Design1) 充分考虑电容器使用和安装条件在产品目录的规定范围内Please make sure the environmental and mounting conditions to which the capacitor will be exposed are within the conditions specified in catalogue.2) 工作温度和施加的纹波电流应在产品目录的规定范围内Operating temperature and applied ripple shall be within specification.3) 在设计电路时，应选择*合寿命要求的产品Appropriate capacitors which comply with the life requirement of the products should be selected when designing the circuit.4) 铝电解电容器是有*性的，不应加反向电压或交流电压。对可能出现反向电压的电路，应选择双*性电容器。注意：即使双*性电容器，也不能直接用于纯交流电路Aluminum electrolytic capacitors are polar. Make sure that no reverse voltage or AC voltage is applied to the capacitors. Please use bi-polar capacitors for a circuit that can possibly see reversed polarity.Note: Even bi-polar capacitors cannot be used for AC voltage application.5）对需要快速和频繁充放电的电路，不应使用铝电解电容器，而应选择*设计的具有长寿命的电容器Do not use aluminum electrolytic capacitors in a circuit that requires rapid and very frequent charge / discharge.In this t*e of circuit, it is necessary to use a special design capacitor with extended life characteristics.6）不应使用过载电压Do not apply excess voltage.① 直流电压与纹波电压叠加后的峰值电压不应*过额定工作电压Please pay attention to that the peak voltage, which is DC voltage overlapped by ripple current, will not exceed the rated voltage.② 若2个以上电容器串联，应*施加电压低于额定值，而且要并联一个平衡电阻，以使每个电容器所加电压相等。In the case where more than 2 aluminum electrolytic capacitors are used in series, please make sure that applied voltage will be lower than rated voltage and the voltage will be applied to each capacitor equally by using a balancing resistor in parallel with the capacitor7）电容器不能应用于下述环境条件下：Aluminum electrolytic capacitors shall not be used under the following environmental conditions:①(a) 电容器被暴露于水（包括浓缩液）、盐水或油中。Capacitors will be exposed to water (including condensation), brine or oil.(b) 周围环境中有氢化硫、亚*、亚硝酸、氯气、溴气、溴化甲烷、氨气等有毒气体。Ambient conditions that include toxic gases such as hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, bromine, methyl bromide, ammonium, etc.(c) 周围环境中有臭氧、紫外线及辐射。Ambient conditions that expose the capacitor to ozone, ultraviolet ray and radiation.② 严重的振动及机械冲击*过产品目录的规定范围。Severe vibration and physical shock conditions that exceed specification.振动的测试条件如下Vibration test condition:振动频率范围 ： 10-55-10Hzvibration frequency range : 10～55～10Hz扫描频率 ： 10-55-10Hz/分钟sweep rate : 10～55～10Hz/minute扫描方式 ： 对数sweep method : logarithmic振幅或加速度 ：1.5mm (*大加速度为10G)amplitude or acceleration : 1.5mm (max. acceleration is 10G)振动方向 ： X、Y、Z方向direction of vibration : X, Y, Z direction测试时间 ： 每个方向2小时testing time : 2 hours per each direction冲击一般不适用。Shock is not applicable normally.如有*要求，请与我们销售部门联系。If a particular condition is required, please contact our sales office.8） 电解液主要化学溶剂及电解纸为易燃物，且电解液导电。当电解液与PC板接触时，可能会腐蚀PC板上的线路，或造成短路，以致产生烟或着火。因此在电容器封口下端不应有任何线路。The main chemical solution of the electrolyte and the separator paper used in the capacitors are combustible. The electrolyte is conductive. When it comes in contact with the PC board, there is a possibility of pattern corrosion or short circuit between the circuit pattern, which could result in *oking or catching fire. Do not locate any circuit pattern beneath the capacitor end seal.9） 设计线路板时应*发热元器件不靠近铝电解电容器或PC板的另一面，避免其正好在电容器的下面。Do not design a circuit board that the heat generating components are placed near the aluminum electrolytic capacitor or on the reverse side of PC board, if that just under the capacitor.10） 设计线路板时应考虑到电容器的电性能可能随温度和频率的变化而变化。Electrical characteristics may vary depending on changes in temperature and frequency. Please consider this variation when you design circuits.11） 当2个以上电容器并联时，应考虑到通过这些电容器的电流平衡。When you install more than 2 capacitors in parallel, please consider the balance of current flowing into the capacitors.12） 在双面线路板上安装电容器时，电容器的安装位置应避开多余的基板孔和过孔。While mounting capacitors on double-side PC board, the capacitors should be away from those unnecessary base plate holes and connection holes.B）安装Mounting1） 一旦电容器经过安装及加载，不要再试图用于其他线路板或其他用途。Once a capacitor has been *embled in the set and power applied, do not attempt to re-use the capacitor in other circuits or application.2） 贮存*过2年的电容器，其漏电流可能*。若漏电流*，请使用1KΩ电阻做充电处理。Leakage current of the capacitors that have been stored for more than 2 years may increase. When leakage current has increased, please perform a voltage treatment using a 1kΩ resistor.3） 在将电容器安装在PC板之前，请确认其规格和*性。Please confirm specifications and polarity before installing capacitors on the PC board.4） 不要将电容器掉在地上，或不要使用掉在地上的电容器。Do not drop capacitors on the floor, nor use a capacitor that was dropped.5） 安装时请不要损伤电容器。Do not deform the capacitor during installation.6） 请注意贴片机的吸头、产品检测夹具或对中装置对电容器的机械冲击。Please pay attention to the mechanical shock to the capacitor by suction nozzle of the automatic insertion machine or automatic mounter, or by product checker, or by centering mechani*.7） 回流焊Reflow soldering① 请遵守产品目录中的回流焊条件。Please follow “Reflow Soldering Conditions” in catalogue.② 当使用*加热时，请注意加热程度，因为*吸收率会随着电容器颜色和大小的不同而改变。When an infrared heater is used, please pay attention to the extent of heating since the absorption rate of infrared will vary due to difference in the color and size of the capacitor.8） 将电容器焊接在PC板后，不要倾斜或扭动电容器。Do not tilt lay down or twist the capacitor body after the capacitor are soldered to the PC board.9） 不要抓住焊接后的电容器搬动PC板。Do not carry the PC board by grasping the soldered capacitor.10)不要让任何物品接触焊接后的电容器。如果PC板堆放储存，请*PC板或其他*部件不触到电容器。Please do not allow anything to touch the capacitor after soldering. If PC boards are stored in stack, please make sure the PC board or other components away from the capacitor.11）焊接后的电容器不应受到任何已焊接PC板或其他元器件热辐射的影响。The capacitors shall not be effected by any radiated heat from the soldered PC board or other components after soldering.12）清洗：Cleaning①不能用卤化清洗剂清洗电容器。如*须使用卤化清洗剂，请与我们销售部门联系。Do not clean capacitors with halogenated cleaning agent. However, if it is necessary to clean with halogenated cleaning agent, please contact our sales office.②推荐清洗方法：Recommended cleaning method使用范围：任何类型及规格Applicable : Any t*e, any ratings清洗方法：浸泡、*声波或其他方法的总清洗时间应在2分钟内。清洗剂温度应在40℃以下。清洗后，应将电容器与PC板一起用热风吹至少10分钟。热风温度应低于电容器工作温度。水洗后若不充分吹干，可能导致外观不良，如座板发胀等。Cleaning conditions : Total cleaning time shall be within 2 minutes by immersion, ultrasonic or other methods. Temperature of the cleaning agents shall be 40℃ or below. After cleaning, capacitors should be dried by using hot air for the minimum 10 minutes along with the PC board mounted. Hot air temperature should be within the maximum operating temperature of the capacitor. Insufficient dryness after water rinse may cause appearance problems, such as bottom-plate bulge and etc.③ 避免使用破坏臭氧层的清洗剂以保护环境。Avoid using ozone destructive substances as cleaning agents for protecting global environment.C）安装后In the Equipment1）不要直接用手接触电容器正负*。Do not directly touch terminal by hand.2）不要在正负*之间用导体连接，也不要在电容器及其附近溅撒导电液体，如酸碱溶液等。Do not link positive terminal and negative terminal by conductor, nor spill conductible liquid such as alkaline or acidic solution on or near the capacitor.3）在使用环境中应避免溅上水或油，避免阳光直射、紫外线照射、辐射、有毒气体、振动或机械冲击。Please make sure that the ambient conditions where the set is installed are free from spilling water or oil, direct sunlight, ultraviolet rays, radiation, poisonous gases, vibration or mechanical shock.D） 维护和检验Maintenance and Inspection请定期检测安装在工业设备上的电容器。检测项目如下：Please periodically inspect the aluminum capacitors that are installed in industrial equipment. The following items should be checked:外观：明显缺陷，如防爆阀打开、电解液泄露等。Appearance: remarkable abnormality such as pressure relief vent opening, electrolyte leaking, etc.电性能：电容量、损耗角正切、漏电流等，具体数据参见产品目录和相关产品规格书。Electrical characteristics: capacitance, dielectric loss tangent, leakage current and etc., which are specified in catalogue or alternate product specification.E）紧急情况In an Emergency1）若看见因防爆阀动作而产生的烟气，请关闭主开关或拔开离合器。If you see *oke due to operation of safety vent, please turn off the main switch or pull out the plug from the outlet.2）若吸入气体或咽下电解液，应立即用水清洗口腔和喉咙。If you breathe the gas or ingest the electrolyte, please wash out your mouth and throat with water immediay.3）若皮肤沾上电解液，请用肥皂和水清洗干净。If your skin is exposed to the electrolyte, please wash it away using soap and water.F） 储存Storage1） 不要将电容器储存在温度和湿度高的地方。储存环境应为温度：5℃-35℃，相对湿度：<75%，储存地点：室内。Do not keep capacitor in high temperature and high humidity atmosphere.Storage conditions should be:Temperature: 5℃～35℃ Humidity : lower than 75% Place : Indoor2）避免电容器的储存环境中有水、盐水或油。Avoid ambient conditions where capacitors are covered with water, brine or oil.4）避免电容器暴露在臭氧、紫外线或辐射中。Avoid ambient conditions where capacitors are exposed to ozone, ultraviolet ray or radiation.G） 处置Disposal请用下面任何一种方法处置电容器：Please take either of the following methods in disposing capacitors.1）在电容器壳体上开孔或将电容器压碎后焚烧。Incinerate them after crushing capacitors or making a hole on the capacitor body.2） 如不能进行焚烧，请交给废物处理机构进行填埋。If incineration is not applicable, hand them over to a waste disposal agent and have them buried in landfills."铝电解电容器的寿命计算方法寿命估算(Life Expectancy)：电解电容器在*高工作温度下，可持续动作的时间。Lx=Lo*2(To-Ta)/10Lx=实际工作寿命Lo=*寿命To=*高工作温度(85℃or105℃)Ta= 电容器实际工作周围温度Example： 规范值105℃/1000Hrs65℃寿命推估：Lx=1000*2(105-65)/10实际工作寿命：16000Hrs高温负荷寿命(Load Life)将电解电容器在*高工作温度下，印加额定工作电压，经一持续规定完成时间后，须*合下列变化：Δcap： 试验前之值的20%以内tanδ： 初期特性规格值的200%以下LC ： 初期特性规格值以下高温放置寿命(Shelf Life)：将电解电容器在*高工作温度下，经一持续规定完成时间后，须*合下列变化：Δcap: 试验前之值的20%以内tanδ:初期特性规格值的200%以下LC:初期特性规格值以下高温充放电试验(Charge/Discharge Test)将电解电容器在*高工作温度下，印加额定工作电压，经充电30秒后再放电330秒为一cycle，如此经1,000 cycles后，须*合下列变化：Δcap : 试验前之值的10%以内tanδ : 初期特性规格值的175%以下LC : 初期特性规格值以下涟波负荷试验(Ripple Life)将电解电容器在*高工作温度下，印加直流电压及*大涟波电流（直流电压 *大涟波电压峰值=额定工作电压），经一持续规定完成时间后，须*合下列变化：Δcap : 试验前之值的20%以内tanδ : 初期特性规格值的200%以下LC : 初期特性规格值以下常用电解电容公式容抗 : XC=1/(2πfC) 【Ω】感抗 : XL=2πfL 【Ω】阻抗 : Z=√*R2 (XL-XC)2 【Ω】涟波电流 : IR=√(βA△T/*R) 【mArms】功率 : P=I2*R 【W】谐振频率 : fo=1/(2π√LC) 【Hz】型号众多，不能一一上传。产品没有全部发布，需要其它型号的朋友，请用以下方式垂询：东莞市日旺电子有限公司直线：86-769-87864412(10线)传真：86-769-87864413手机:13798814438(陈先生)手机:13138834020(黄)Q Q:892218806 1750229156529711731 1534890610MSN：riwangdg@hotmail.comriwangdz@hotmail.com：china@riwangdg.com网址：www.riwangdg.com地址：中国广东省东莞市塘厦镇第一工业区

企业名：东莞市日旺电子有限公司

类型：

电话： 86 0769 87864412

联系人：陈雷

地址：广东东莞中国 广东 东莞市 塘厦镇第一工业区